Opening Hour

Mon - Fri, 8:00 - 9:00

WhatsApp

+8618037022596

Reasons Your Gas Fireplace Isn''t Working Fireplace Experts

+

In general, propane powered fireplaces will produce more soot than natural gas fireplaces. If you notice excess soot build up, here are a few common culprits. Improper Airflow: Ensure that there is a proper ratio between the flame’s gas and oxygen; a flame that has too much gas will produce more soot.

Furnace Flame Sensor | Repair and Replace YouTube

+

Nov 20, 2017· In this episode of Repair and Replace, Vance shows how to replace the flame sensor in a gas furnace. The flame sensor monitors the burner. If no flame is det...

The Basic Understanding of a Gas Fireplace Millivolt System

+

Jan 30, 2015· The most common type of gas fireplace uses a millivolt ignition system. The piezo ignitor is usually connected to a button that generates a spark when depressed. The pilot flame heats both the ...

Flame Sensor What is this furnace part and how to fix it

+

The flame sensor’s job is to create a current of electricity. One note on safety: This current has to be on the proper level to function. The furnace will come with a control board that measures this reading once the ignition process starts. If the control board does not read the correct level of electrical current, the furnace will cut off ...

Gas Flame Thermocouple Sensors Troubleshooting …

+

The thermocouple on gas fired heating appliances is mounted to sense the presence of a gas flame or gas pilot flame. The other end of the thermocouple''s tubing connects to a port on the gas regulator or gas valve But not all of these systems use a thermocouple. Some gas fired heating equipment relies on an electronic ignition to ignite the flame.

How To Clean a Flame Sensor Furnace Troubleshooting ...

+

Common replacement flame sensors:Goodman: : : , Luxaire, Tempstar: http:/...

Oxygen Depletion Sensor (ODS) Gas Fireplace Repair

+

Nov 04, 2015· The American National Standards Institute mandates that unvented gas heaters to be automatically turned off when the specified level of oxygen is not achieved. The automatic shutoff is controlled by the oxygen depletion sensor or ODS pilot system. The ODS system is part of the pilot assembly designed to regulate the flame performance.

Problem with Majestic Gas Fireplace

+

Good flame impingement here will cause the sensor to glow red. If the flame is too weak to contact the sensor steady...look for adjustment or obstruction. If the flame lifts off the sensor...look for a leak in the vent(or other venting issues). If the flame is blowing away from sensor...look for a missing shield or a log out of place. GOOD LUCK

Parts of a Fireplace: Gas Fireplace Parts You Should Know

+

The Hearth. When most people first look at a fireplace, their eyes naturally gravitate toward the box that houses the flames. This cavernous area is called the , the firebox works in tandem with an important base made from fireproof material called a fireplaces, like traditional wood burning fireplaces, are constructed with a protective hearth.

Why do flame sensors fail?

+

If no flame is present, the sensor stops or prevents the flow of gas from the gas valve, thus preventing the dangerous situation of gas flowing into the appliance when there is no flame to burn it. Flame sensors and thermocouples are simple parts that wear out and fail over time, and most are easy to replace.

Gas Fireplace Pilot Light On But Won’t Start? (We Have A ...

+

Sometimes if the gas fireplace pilot light is on but won’t start the fireplace, it can be as simple as a faulty fireplace vent cap. If a cold draft blows the pilot out on a regular basis, relight the pilot and check out the vent cap. If it continues to extinguish the flame, replace the vent cap; if you don’t have one, call in a service ...

How to Test a Flame Sensor | Hunker

+

Jul 05, 2021· Although designs vary somewhat, a typical flame sensor is a 2 to 4inch metal rod with a porcelain base and is connected to the gas valve by a wire. It''s mounted on the burner housing in such a way that the metal rod is in contact with the flame when the gas is burning.

Gas Fireplace Automatic Ignition Sensor Gas grill repair ...

+

Dec 10, 2012· Gas fireplace pilot assembly appears to have 2 electrodes but one is a sensor that reads electric signal passing through the flame. This is a simple unbreakable design that keeps thousands of people safe from gas leaks and …

Gas Log 101 Troubleshooting National Fireplace Institute ...

+

change in flame height for a 6 hour period. Temp/Timer Mode= If the ambient room temp changes, the flame height will adjust automatically to maintain set temp and the fire will continue to function normally. Valve will turn to pilot flame if the set temp ambient temp remain the same over a 6 hour period. Burner Installation Procedures

Why Does My Gas Fireplace Keep Shutting Off? HVAC BOSS

+

Dec 24, 2020· Thermocouple Sensor Issues. On a gas fireplace, you will have a thermocouple that helps to regulate temperature by keeping the pilot light at a certain height and temperature. Gas fireplaces have thermocouple sensors on them for a couple of reasons: To allow you to control the temperature of the room.

How to Clean the Thermocouple in a Gas Fireplace | Hunker

+

Step 5. Close the fireplace access panel and restore the gas supply to the fireplace. Contact a service professional if the problems with the fireplace continue or if you are not certain of your ability to access, identify or clean the thermocouple. If you smell a gas odor even after shutting off the gas valve prior to the cleaning task, leave ...

Leave a comment